Certificate IV in Engineering

Lead College Pty Ltd

CRICOS Institution Code 03636F

Duration

104 weeks

Delivery

Blended (Face to Face + Online). This program is delivered and assessed through a combination of classroom-based learning, simulated industry workplace activities, and supervised online study.

Study Load

Blended · Approximately 10 hours per week of unsupervised study, including reading, research, and revision of previous lessons

Intakes

—

Course Overview

About This Course

This qualification defines the skills and knowledge required of a higher-level engineering tradesperson within the metal, engineering, manufacturing, and related industries. It applies to a broad range of advanced engineering work, including but not limited to: refrigeration and air conditioning, casting and moulding, CNC programming, fluid power, heavy fabrication, instrumentation, maintenance, plant mechanics, marine electronics, mechatronics, patternmaking, robotics, toolmaking, welding, and watch and clock servicing and repair. This may also include post-trade work. Graduates will gain the capability to: Apply quality control techniques Interpret complex instructions and procedures Work independently or as part of a team with minimal supervision Use effective interpersonal and communication skills Exercise discretion and judgement within defined responsibilities Guide and assist others in a trade environment Perform incidental non-trade tasks supporting primary duties Inspect materials and products for compliance with standards Operate lifting equipment related to their tasks Support training delivery alongside supervisors and trainers While there are no formal entry requirements, it is expected that learners are qualified tradespeople with access to structured on- and off-the-job training, or apprentices under an Australian Apprenticeship arrangement. This qualification is not intended for pre-employment or pre-apprenticeship use. No licensing, legislative or certification requirements apply to this qualification at the time of publication. However, in some jurisdictions units in this qualification may require a license. Licensing information is included in the relevant units of competency.

Where You Can Study

Available Locations

Perth

15 Leila St, Cannington, WA 6107

Open in Maps ↗

Eligibility

Entry Requirements

General Requirements

The following are the Admission requirements of Lead college: Must be 18 years of age or older at the time of course commencement. Prospective students may be required to undertake a Language, Literacy and Numeracy (LLN) and/or a pre-enrolment interview. Must have completed MEM31922 Certificate III in Engineering – Fabrication Trade with Lead College or another institute with similar elective. Must demonstrate English level of IELTS 6.0 overall with no band less than 5.5 or equivalent, such as: IBT 60 PTE 50 CAE 169 OET B General English Advanced or equivalent MOI Certificate Duolingo 95 MET LANGUAGECERT Academic CELPIP General Certificate IV or higher qualification with an Australian institution. Must have basic digital literacy, including the ability to confidently use the internet and common software applications for learning purposes, completing assignments, and engaging with course content. Must be able to participate in training within a simulated workplace environment, including performing manual handling tasks.

Career & Study Pathways

Where this takes you

Career Opportunities

These are potential routes for career progression: Welding, Boilermaking, Surface finishing, Sheet metalworking.

Course Content

Units of Competency

All Units29 units

MEM09002

Interpret technical drawing

MEM13015

Work safely and effectively in manufacturing and engineering

MSMENV272

Participate in environmentally sustainable work practices

MEM16006

Organise and communicate information

MEM11011

Undertake manual handling

MEM12023

Perform engineering measurements

MEM12024

Perform computations

MEM14006

Plan work activities

MEM17003

Assist in the provision of on-the-job training

MEM16008

Interact with computing technology

MEM18001

Use hand tools

MEM18002

Use power tools/hand held operations

MEM12007

Mark off/out structural fabrications and shapes

MEM12006

Mark off/out (general engineering)

MEM18003

Use tools for precision work

MEM06003

Carry out heat treatment

MEM18055

Dismantle, replace and assemble engineering components

MEM05014

Monitor quality of production welding/fabrications

MEM05006

Perform brazing and/or silver soldering

MEM05050

Perform routine gas metal arc welding

MEM05004

Perform routine oxy fuel gas welding

MEM05085

Select welding processes

MEM05052

Apply safe welding practices

MEM05012

Perform routine manual metal arc welding

MEM05049

Perform routine gas tungsten arc welding

MEM05007

Perform manual heating and thermal cutting

MEM09003

Prepare basic engineering drawing

MEM05037

Perform geometric development

MEM05005

Carry out mechanical cutting

Common Questions

Frequently Asked Questions

What are the English language requirements for this course?

Applicants must demonstrate an English level of IELTS 6.0 overall with no band less than 5.5, or an equivalent qualification such as IBT 60, PTE 50, CAE 169, OET B, General English Advanced or equivalent, MOI Certificate, Duolingo 95, MET, LANGUAGECERT Academic, CELPIP General, or a Certificate IV or higher qualification with an Australian institution.

What are the fees for the Certificate IV in Engineering?

The tuition fee for MEM40119 Certificate IV in Engineering (CRICOS Course Code: 112672F) is listed alongside MEM31925 Certificate III in Engineering – Fabrication Trade in the fee schedule. The Certificate III has a tuition fee of $7,000 and material/placement fee of $1,000. Please contact Lead College's marketing staff or a consultant for the specific fee applicable to the Certificate IV in Engineering.

What prerequisite qualification do I need to enrol in this course?

You must have completed MEM31922 Certificate III in Engineering – Fabrication Trade with Lead College or another institute with a similar elective. This qualification is not intended for pre-employment or pre-apprenticeship use, and it is expected that learners are qualified tradespeople with access to structured on- and off-the-job training, or apprentices under an Australian Apprenticeship arrangement.

What pathways are available after completing the Certificate IV in Engineering?

Additional training opportunities stemming from this certification consist of pursuing the Advanced Trade Diploma in Engineering or other suitable qualifications. Career progression pathways include welding, boilermaking, surface finishing, and sheet metalworking.

How is the Certificate IV in Engineering assessed?

Students are assessed through a range of methods including written questions or reports to demonstrate understanding of theoretical concepts, practical activities or projects simulating real-world tasks, case study analysis for critical thinking, direct observation during practical sessions or workplace activities, and supervised work placement where applicable. Students must successfully complete all units to receive the MEM40119 Certificate IV in Engineering certificate.

Application

How to Apply

Three simple steps to get enrolled

Step 01

Enquire

Click "Enquire Now" and tell us a little about yourself. It's free and takes 2 minutes.

Step 02

Submit Documents

Our team will guide you on exactly which documents to prepare and submit.

Step 03

Get Enrolled

Receive your offer letter and confirm your enrolment. Welcome to the course!

Course Snapshot

Typical Salary (AUD)

Entry-level (0-2 years)$72,000 – $95,000/yr

Early Career (2-5 years)$95,000 – $130,000/yr

Mid-Level (5-10 years)$130,000 – $165,000/yr

Career Paths

Graduate Construction Manager
Site Manager
Project Manager
Construction Project Manager
Contracts Administrator

Key Skills

Construction project planning and scheduling (including Gantt charts and critical path method)
Cost estimation, budgeting, and quantity take-off
Contract administration and procurement management
Reading, interpreting, and producing construction drawings and specifications
Work Health and Safety (WHS) compliance and site safety management

Full course overview

💬

Need guidance?

Free advisor support

Our advisors help international students choose the right course and navigate visa pathways — at no cost.

Hear From the Students

Honestly I was lost when I first started looking at Australian colleges. There are just too many options and every agent gives you different info. A friend told me about FindTheCourses and within a week I had shortlisted 3 programs that actually matched my budget and visa situation. My advisor Sanjay was super helpful — never felt like I was being pushed into anything.

Priya Sharma

India

Master of Nursing · Griffith University

Promote your Institution with Find the Courses